Truma ZR 80 cowl outer part black 36151-09 - outer part of the wall cowl for Combi heaters
- Truma cowl outer part ZR 80 black, no. 36151-09 - outside part of the wall cowl of Truma Combi (E) heaters and next generation Combi D (E). Fixed with 2 screws to the ZR 80 inner part. Without inner part and ducts.
Truma cowl outer part ZR 80 in black, no. 36151-09 is the outside part of the wall cowl of Truma Combi heaters. It is fitted onto the ZR 80 cowl inner part from outside the vehicle and fixed with two screws. Exhaust gas leaves through the cowl while combustion air is drawn in at the same time. The part is sold separately - as a replacement for a damaged or faded cover, or to complete the ZR 80 wall cowl set, which does not include the outer part.
What it does
- outer cover of the ZR 80 wall cowl, visible on the side wall of the motorhome or caravan
- exhaust gas leaves and combustion air is drawn in through the cowl openings (duct in duct system)
- colour black - to match the vehicle wall
- fits the ZR 80 inner part - the complete cowl consists of an inner and an outer part
- available in five colours: cream white, bianco (white), light grey, black and anthracite
Which heaters
- ZR 80 wall cowl of Truma Combi (E) gas heaters, e.g. Combi 4, Combi 6, Combi 4 E, Combi 6 E
- listed by Truma among the Combi (E) accessories as cowl outer part ZR 80, no. 36151-09
- Truma recommends two colour versions of the outer part - black and anthracite - also for the next generation Combi D (E) heaters. This is one of them.
- when replacing only the cover, the existing inner part stays in place
Replacing the cover step by step
- switch off the heater and let the cowl cool down
- remove the 2 screws of the old outer part and take it off
- check the seal and the inner part
- fit the new outer part so that the arrow on the cowl points up
- fix it with the 2 stainless steel screws B 3.5 x 25
Installing the wall cowl according to Truma instructions
- the cowl is installed with the arrow pointing up, on an even wall surface around which wind can flow from all sides
- drill a Ø 83 mm hole in the wall; line any cavities around the hole with wood
- the cowl is sealed with a rubber seal; on textured surfaces also use flexible body sealant - not silicone
- the inner part is fixed with 6 screws, the outer part is fitted onto it and fixed with 2 screws B 3.5 x 25
- the AA 3 exhaust duct (Ø 55 mm) must be 10% longer than the ZR 80 combustion air intake duct (Ø 80 mm)
- a ZR 80 duct of 60-100 cm may rise or fall by max. 20 cm, a duct of 100-200 cm may only rise
- ducts longer than 60 cm are fixed to the wall with at least one ZRS clamp
- keep at least 10 mm between the exhaust system and heat-sensitive parts
For the Combi exhaust system Truma only permits original parts: AA 3 exhaust duct (39320-00), ZR 80 combustion air intake duct (39580-00) and clamps - the appliance is tested and approved only with these. Installation and inspection of the gas system should be carried out by an authorised specialist.
Related products
- Cowl outer part ZR 80, cream white (36151-01)
- Cowl outer part ZR 80, bianco (36151-05)
- Cowl outer part ZR 80, light grey (36151-08)
- Cowl outer part ZR 80, anthracite (36151-10)
- Wall cowl set ZR 80 (36240-01) - inner part, ducts and clamps
- Cowl inner part ZR 80 (36140-01) with clamps
- Clamp ZRS Ø 80 mm for fixing the ZR 80 duct
Technical data
| Parameter | Value |
|---|---|
| Brand | Truma |
| Model | Cowl outer part ZR 80 |
| Manufacturer number | 36151-09 |
| Colour | black |
| Type | outer part of the wall cowl |
| Fits | cowl inner part ZR 80 (36140-01) |
| Heaters | Truma Combi (E), next generation Combi D (E) |
| Fixing | 2 screws B 3.5 x 25 |
| Wall hole for the cowl | Ø 83 mm |
| Contents | 1 cowl outer part, without inner part and ducts |
Questions and answers
Is the cowl inner part included?
No. This is the outer part only. The ZR 80 inner part is available separately or in the wall cowl set with ducts and clamps.
Does the colour affect performance?
No, all colours have the same design. You choose the colour to match the vehicle wall.
Will it fit my heater?
It fits the ZR 80 wall cowl of Truma Combi (E) heaters and the next generation Combi D (E). Before ordering, compare the part number on the old cover or in the heater manual.
Can I replace it myself?
The cover alone is replaced by undoing 2 screws. If the inner part or the ducts have to be removed, work on the gas system should be done by an authorised specialist.
Manufacturer
Truma Gerätetechnik GmbH & Co. KG, Wernher-von-Braun-Straße 12, 85640 Putzbrunn, Germany.