GOK straight fitting type G-MS RVS 8 x RVS 8, brass - for the LPG system in a motorhome or caravan
- GOK straight fitting type G-MS in brass, connections RVS 8 x RVS 8, series L. With a type M-MS nut and a type D-MS cutting ring. For metal gas pipes, including the LPG system of a motorhome or caravan.
This straight fitting type G-MS from GOK joins two pipes with RVS 8 x RVS 8 connections, that is a cutting-ring joint for pipe with an outside diameter of 8 mm on both sides. It belongs to series L and is designated EN ISO 8434-1 - SC, which means a straight coupling. It is supplied with a type M-MS nut and a type D-MS cutting ring. The material is brass, given by GOK as CW614N or CW617N. The body is straight, not an elbow. It is used on metal gas pipework, including the LPG system of a motorhome or caravan.

Key features
- straight fitting type G-MS from GOK, designation EN ISO 8434-1 - SC
- connections RVS 8 x RVS 8, series L
- type M-MS nut and type D-MS cutting ring included
- material: brass CW614N or CW617N
- straight coupling, not an elbow
- cutting-ring fittings with a DVGW type-examination certificate to DIN 3387-1
- for metal gas pipes, including the LPG system of a motorhome or caravan
What this fitting is for
The type G-MS fitting joins two lengths of 8 mm pipe in a straight line. A typical place is a joint between two pipes in the LPG system of a motorhome or caravan, or a repair of a pipe run where the direction does not change. An elbow type W-MS is a different article and is not this product.
With copper or aluminium pipe GOK requires a reinforcing sleeve. For 8 x 1 mm copper pipe that is the brass type VSH-MS sleeve (reinforcing sleeve type VSH-MS AD 8 x 1). For aluminium pipe use a steel sleeve, not a brass one. In Germany, the installation of copper pipes with reinforcing sleeves in an LPG system is permitted only for caravans, recreational vehicles and marine use.
The type M-MS nut (coupling nut type M-MS 8 mm) and the type D-MS ring (cutting ring type D-MS 8 mm) are part of this fitting. You can also buy them separately as spares. Do not confuse this variant with the straight type G fitting, which is made of steel. This card is only for the brass type G-MS.
How it is built and what the markings mean
The body is straight, with a hexagon in the middle so you can hold it with a spanner. At each end there is a cone for the cutting ring and a thread for the type M-MS nut. The RVS 8 connection is a cutting-ring joint for 8 mm pipe. The designation SC according to EN ISO 8434-1 means a straight coupling.
The seal is made when the pipe, a reinforcing sleeve if required, the type D-MS ring and the type M-MS nut are correctly assembled on the cone of the fitting body. The fitting does not use a separate flat gasket. GOK states that cutting-ring fittings have a DVGW type-examination certificate to DIN 3387-1. That standard covers joints in metal gas pipes, for example in the scope of the TRF. Design details are set mainly in EN ISO 8434-1 and DIN 2353.
Overall dimensions of the complete fitting are not given on the official GOK product page, so a length and a spanner size are not listed here. The pipe diameter, type and series come from the official product page.
How to fit it
- Work on a gas system only after the pressure has been fully released and in line with the rules that apply, for example the TRF. If you are not qualified to do this work, have a competent person fit the joint.
- Cut both pipes square. GOK does not allow a pipe cutter or an angle grinder. Lightly deburr the ends inside and outside, then clean them. A pipe that is cut at an angle or poorly deburred weakens the seal and the life of the joint.
- If the pipe is thin-walled or made of a soft material, such as copper or aluminium, drive a reinforcing sleeve into the pipe up to the knurled rim, using a plastic or rubber hammer. For aluminium pipe use a steel sleeve.
- On each pipe end, slide the nut on first, then the cutting ring, with the cutting edge facing the pipe end. The wrong ring position means an incorrect assembly.
- Push the pipe fully home into the cone of the fitting body. Tighten the nut by hand until the body, the ring and the nut meet. Then tighten the nut with an open-ended spanner by about 1 and 1/2 turns on first assembly, holding the fitting body with a second spanner. The pipe must not turn. A different tightening method reduces the strength of the joint and can cause a leak or the pipe to pull out. Repeat the same steps on the other side of the fitting.
- After assembly, test both joints for tightness as required, for example with a foaming leak-detection fluid. After any later disconnection, tighten the nut again with the same care as for a full assembly, once more holding the body.
What to watch out for
- This is a gas-system part. Escaping gas is flammable. If you smell gas or suspect a leak, shut off the gas supply at once and do not use naked flames or electrical switches nearby.
- Undo or tighten the fitting only after the pressure has been fully released.
- With copper or aluminium pipe always use a reinforcing sleeve. For aluminium use only a steel sleeve, not a brass one.
- In Germany, copper pipes with reinforcing sleeves in an LPG system are permitted only in caravans, recreational vehicles and on boats.
- GOK does not publish a numerical working pressure on this fitting page. Do not exceed the figures in the cutting-ring fitting data sheet or the limits of the rest of the system.
Care
Before assembly, check that the nut threads and the cones of the body are not damaged or dirty, and that the rings are not deformed. Do not use damaged parts. Store the fitting in a dry place. After the season, or after any work on the gas system, check the joints for tightness. When you reassemble a joint, follow the GOK installation instructions. Replace a damaged ring with a new type D-MS ring for 8 mm.
Technical data
| Feature | Value |
|---|---|
| Type | straight fitting type G-MS |
| Brand | GOK |
| Connections | RVS 8 x RVS 8 (8 mm pipe on both sides) |
| Series | L |
| Designation according to EN ISO 8434-1 | SC |
| Nut | type M-MS, included |
| Cutting ring | type D-MS, included |
| Material | brass CW614N or CW617N |
| Fitting certificate | DVGW type examination according to DIN 3387-1 |
| Shape | straight, not an elbow |
| Use | metal gas systems, including the LPG system of a motorhome or caravan |
Frequently asked questions
Is this a 90 degree elbow?
No. Type G-MS is a straight fitting. An elbow is a different type, for example type W-MS, and is not this product.
What does RVS 8 mean?
It is a cutting-ring connection for pipe with an 8 mm outside diameter. Both ends of the fitting have the same connection.
What is included?
The type G-MS body, type M-MS nuts and type D-MS cutting rings. The reinforcing sleeve is not included and is needed separately for copper or aluminium pipe.
What is it made of?
Brass. In the GOK documentation the material is given as CW614N or CW617N. This is the type G-MS variant, not the steel type G.
Is a sleeve needed for copper pipe?
Yes. GOK requires a reinforcing sleeve with copper or aluminium pipe. For 8 x 1 mm copper pipe that is the brass type VSH-MS sleeve. For aluminium, a steel sleeve.
Does the fitting have DVGW approval?
GOK states that cutting-ring fittings have a DVGW type-examination certificate to DIN 3387-1.





