GOK coupling nut type M-MS 8 mm, brass, female thread M14 x 1.5 - for cutting-ring fittings, series L
- GOK coupling nut type M-MS for 8 mm pipe, with a female M14 x 1.5 thread, series L. For cutting-ring fittings to DIN 2353 and EN ISO 8434-1. Designation N according to EN ISO 8434-1.
This brass coupling nut type M-MS from GOK is made for cutting-ring fittings on pipe with an outside diameter of 8 mm. It has a female M14 x 1.5 thread and belongs to series L according to DIN 3870. In EN ISO 8434-1 it is designated N. The material is brass, given by GOK as CW614N or CW617N. The nut screws onto the fitting body and presses the cutting ring into the cone, which seals the pipe joint. It is used on metal gas pipework, including the LPG system of a motorhome or caravan, in line with the rules that apply.

Key features
- coupling nut type M-MS from GOK
- for pipe with an outside diameter of 8 mm
- female thread M14 x 1.5
- series L according to DIN 3870
- designation N according to EN ISO 8434-1
- material: brass CW614N or CW617N
- for cutting-ring fittings according to DIN 2353 and EN ISO 8434-1
- intended for metal gas pipework, including LPG systems
What this nut is for
The type M-MS nut is part of a cutting-ring fitting. As you tighten it, the ring bites into the pipe and into the cone of the fitting body, so the joint holds and seals without soldering. It fits series L fittings for 8 mm pipe, for example the straight type G-MS fitting with RVS 8 x RVS 8 connections, which is in this shop as straight fitting type G-MS RVS 8 x RVS 8.
You can buy it as a spare if the nut on a fitting is damaged, missing or has a damaged thread. A complete joint also needs a type D-MS cutting ring for 8 mm (cutting ring type D-MS 8 mm) and the fitting body. With copper or aluminium pipe GOK requires a reinforcing sleeve. For 8 x 1 mm copper pipe that is the brass type VSH-MS sleeve (reinforcing sleeve type VSH-MS AD 8 x 1). For aluminium pipe use a steel sleeve, not a brass one.
This is the brass type M-MS variant, not the steel type M nut. Both have an M14 x 1.5 thread for 8 mm series L pipe, but they differ in material. Match the nut to the material of the fitting body.
How it is built and what the markings mean
The body is hexagonal so you can tighten it with an open-ended spanner. Inside is an M14 x 1.5 thread. The 8 mm size in the GOK data is the outside diameter of the pipe, not the thread diameter. The letter N in EN ISO 8434-1 stands for the nut, not for a separate size series. The dimensional series is L according to DIN 3870.
Type G-MS fittings that use this nut have, according to GOK, a DVGW type-examination certificate to DIN 3387-1. That standard sets the requirements and tests for cutting-ring fittings (smooth-pipe couplings) used to join metal gas pipes, for example in the scope of the TRF. Design details are set mainly in EN ISO 8434-1 and DIN 2353.
The nut does not seal on its own. The seal is made only when the cutting ring, the pipe and the cone of the fitting body are assembled and tightened as described in the GOK installation instructions.
How to fit it
- Work on a gas system only after the pressure has been fully released and in line with the rules that apply, for example the TRF. If you are not qualified to do this work, have a competent person fit the joint.
- Cut the pipe square. GOK does not allow a pipe cutter or an angle grinder. Lightly deburr the ends inside and outside, then clean them. A pipe that is cut at an angle or poorly deburred weakens the seal and the life of the joint.
- If the pipe is thin-walled or made of a soft material, such as copper or aluminium, drive a reinforcing sleeve into the pipe up to the knurled rim, using a plastic or rubber hammer. For aluminium pipe use a steel sleeve.
- Slide the nut onto the pipe first, then the cutting ring, with the cutting edge facing the pipe end. The wrong ring position means an incorrect assembly.
- Push the pipe fully home into the cone of the fitting body. Tighten the nut by hand until the body, the ring and the nut meet. Then tighten the nut with an open-ended spanner by about 1 and 1/2 turns on first assembly, holding the fitting body with a second spanner. The pipe must not turn. A different tightening method reduces the strength of the joint and can cause a leak or the pipe to pull out.
- After assembly, test every joint for tightness as required, for example with a foaming leak-detection fluid. After any later disconnection, tighten the nut again with the same care as for a full assembly, once more holding the fitting body.
What to watch out for
- This is a gas-system part. Escaping gas is flammable. If you smell gas or suspect a leak, shut off the gas supply at once and do not use naked flames or electrical switches nearby.
- Undo or tighten the fitting only after the pressure has been fully released.
- With copper or aluminium pipe always use a reinforcing sleeve. For aluminium use only a steel sleeve, not a brass one, because of corrosion.
- GOK does not publish a numerical working pressure on this nut page. Do not exceed the figures in the cutting-ring fitting data sheet or the limits of the rest of the system.
- Do not mix this brass type M-MS nut with a steel type M or type G fitting if GOK specifies a matching material pair. For a type G-MS fitting use a type M-MS nut and a type D-MS ring.
Care
Before assembly, check that the nut thread is not damaged, flattened or dirty. Do not use a damaged nut. Store it in a dry place, away from strong acids or agents that could attack brass. After the season, or after any work on the gas system, check the joints for tightness. When you reassemble a joint, follow the GOK installation instructions and do not tighten by feel beyond the method given.
Technical data
| Feature | Value |
|---|---|
| Type | coupling nut type M-MS |
| Brand | GOK |
| Pipe diameter (connection A) | 8 mm |
| Thread | female M14 x 1.5 |
| Series | L according to DIN 3870 |
| Designation according to EN ISO 8434-1 | N |
| Material | brass CW614N or CW617N |
| Fitting standards | DIN 2353, EN ISO 8434-1, DIN 3387-1 |
| Use | cutting-ring fittings in metal gas systems, including the LPG system of a motorhome or caravan |
Frequently asked questions
Which pipe does this nut fit?
Pipe with an outside diameter of 8 mm in a series L fitting. The nut thread is female M14 x 1.5.
What does the letter N mean?
It is the nut designation in EN ISO 8434-1, not a separate size series. This nut belongs to series L according to DIN 3870.
What is it made of?
Brass. In the GOK documentation the material is given as CW614N or CW617N.
Is this the nut used on the type G-MS RVS 8 x RVS 8 fitting?
Yes. According to GOK, the straight type G-MS fitting for RVS 8 x RVS 8 comes with a type M-MS nut and a type D-MS ring. This card is the nut on its own, without the ring and without the fitting body.
Is the nut enough for copper pipe?
No. You also need a type D-MS cutting ring, the fitting body and a reinforcing sleeve. For 8 x 1 mm copper pipe that is the brass type VSH-MS sleeve.
Do fittings that use this nut have DVGW approval?
GOK states that its cutting-ring fittings have a DVGW type-examination certificate to DIN 3387-1. This card is for the nut itself, which is a part of those fittings.





